High-accuracy Piling System Used in Construction of Aarah Resort, Maldives

High-accuracy Piling System Used in Construction of Aarah Resort, Maldives

Piling is a vertical structural element with a deep foundation, driven or drilled deep into the ground. In this project, it was necessary to create a deep foundation in a shallow-water sandy area, which has only a shallow foundation. The steps of a traditional piling solution are:

Manual stakeout -> Above-ground markers -> Artificial aim piling

Especially in view of the challenging surface conditions, a traditional piling approach would create a heavy workload in terms of manual stakeout.

- Challenge 1: environmental constraints (marine piling), the markers could move easily and become lost
- Challenge 2: need for pre-work and high-intensity work
- Challenge 3: high labour costs, low work efficiency

(This article is brought to you by ComNav Technology)

Customer    The piling project was awarded to LANKA FOUNDATION AND PILING SERVICES PVT LTD. ComNav Technology supported the project as the piling solution provider.
Date 10/2/2017 - present
Location Maleira Island, south of the Vatu Atoll, Maldives
Project summary Equipment:
- 1x T300 GNSS receiver
- 1x Pilling system tablet (built-in high-accuracy OEM board)
- 2x AT330 GNSS antennas
Software - Pile Master
- Survey Master
Other Power supply, cable, tripod and related accessories


Piling site


Fig 1: The project site

- Better project quality: with the ComNav high-accuracy GNSS engine inside, the piling accuracy was improved to 1-2cm.

- Time savings: no pre-operation was required, which substantially increased the piling efficiency, shortened the construction period, and reduced the labour requirements and construction costs.

- Easy to use: the large-screen (9-inch) high-resolution interface is legible at a glance, offers clear voice navigation is intuitive and easy to understand, allowing for smooth operation even by non-professionals.


Fig 2.1: Construction steps in the Aarah Resort project


Fig 2.3: Construction steps in the Aarah Resort project

The two photos (Figure 2) show the piling, construction and completed phases of the Aarah Resort project. In this large piling project, the aim is to build 64 luxury water villas and 12 beach buildings including a restaurant, bar and spa centre, sports club, children’s club, etc. The project design is based on construction in a shallow-water area with more than 1,200 mini-piles of 300mm in diameter and 6m or 9m in length, while the maximum depth is 3m underground. The high-precision piling system of SinoGNSS provides excellent support service. Because the Aarah Resort is located in the neritic zone, the traditional piling approach would require a large number of surveyors to stake out the location under water in advance. This would not only entail high-intensity work, but would also create a real-time problem: even if the coordinates were measured by lofting very accurately, the primary coordinate markers would soon be out of position due to the movement of the piling machines. This shortcoming would be intensified by strong waves, ocean currents and coral reefs which would further reduce the stakeout accuracy. Furthermore, in the subsequent piling process, the piling accuracy would be reduced due to artificial aiming. During the whole process, surveyors would need to work in the water and fix the piles at short range, which would also create huge potential safety hazards. For all of the above reasons, the traditional piling approach would be a low-efficiency, high-cost and high-risk operation. 

When, LANKA FOUNDATION AND PILING SERVICES PVT LTD was awarded the project, the company was keen to find an efficient way of tackling the challenges. Looking for the best quality piling solution in China, LANKA contacted the piling machine manufacturer XCMG (-www.xcmg.com/en-eu/) chose ComNav Technology as the system provider due to its strong brand and proven experience.

Compared with the traditional piling method, the SinoGNSS intelligent control system for piling is an all-weather, high-accuracy solution with the additional advantages of being widely compatible and easy to manage. Through software system control and real-time processing and display, it can greatly reduce the number of surveyors on site and the labour intensity of their work. The system can provide customers with practical solutions in terms of real-time guidance to the location, shorten the construction period, save construction costs and enable intelligent visualisation and monitoring to ensure high-accuracy construction work.

System design and setup
The system setup comprised a T300 GNSS receiver as base station and an Android industrial-grade piling system tablet as rover, Pile Master software and two sets of AT330 antennas with 30 metres of antenna cable.

Operating procedure
Preliminary data preparation
The control point data was obtained from the project department plus the CAD design drawing of the piling area or the coordinates of the piling location, and the piling point data was imported into the software.


Fig 4: Fixing the base on the first pile with known coordinate


Fig 5: System installation

Set up base station
T300 was set up as base station. The SinoGNSS T300 GNSS receiver is a high-accuracy RTK receiver, which has internal UHF Tx/Rx and 4G internet. It is also rugged, water proof and dust proof in line with the IP67 standard, making it ideal for field survey and mapping. With the T300 set as base station in UHF mode, the 2 Watt internal UHF transmission enabled the work distance to reach 5km, making it convenient for this project.

System installation
Two antennas were installed on the hammer seat, the piling tablet was installed in the driving cab, and antenna cables were laid following the pile-driver routing.

Machine operation
Surveyors followed the guiding interface and voice to drive to the designated location for piling operation (all done by Pile Master software).

1. Coordinates system and input points
The project was built and the coordinate system parameters keyed in, then designed pile coordinates. In this project the DWG file was imported directly into Pile Master for ease of viewing.

Fig 7: DWG file data

2. Calculate the core coordinates of the pile
The three points (two GNSS antennas and one core of pile) were in the fixed triangle. The two GNSS points were obtained by RTK and then used to easily compute the pile points. Pile Master software calculated and transformed the collected parameters to obtain accurate 3D coordinates and the driving parameters of the pile.

3. Piling-friendly user interface of Pile Master
On the one hand, this external output and input unit of the pile driving system forms the basis of the user interface (UI) display, providing piling location guiding information with real-time updates of the calculation parameters. On the other, it facilitates user-friendly interaction with the computer, making it easy to input various parameters of each system.


Fig 9: Pile Master built the triangle module


Fig 10: User-friendly interface of Pile Master

As the first overseas project following the launch of the piling Solution, this project was highly praised by customers. The traditional piling approach entails low-efficiency, time-consuming and labour-intensive work. At the same time, the work site also has a certain degree of danger. SinoGNSS introduces a new high-accuracy and high-efficiency piling solution. Compared with the traditional piling approach, this project required almost no pre-work and suffered no coordinate offset problems due to no pre-lofting. In this respect, the approach has truly helped to achieve real-time, high-precision and efficient piling.

To learn more about ComNav Technology, go to www.comnavtech.com

Make your inbox more interesting

Receive a weekly summary of the biggest news, along with the best stories, case studies, and key market insights.